quilting with rulers Archives - Handi Quilter

Apply binding on the longarm

I’m willing to bet 9 out of 10 of you bought your longarm machine because you were not happy wrestling that large quilt through your domestic machine to do the quilting. Am I right? We solved one problem. But, then what do we do? We finish the beautiful quilting on our longarm, then take the quilt off the frame and wrestle that large quilt through our domestic machine to apply the binding. Let me ask, does that make any sense? I am going to share a little tutorial on how to apply binding on the longarm. Sewing the binding to the front of the quilt, while the quilt is still on the frame. It is quick and easy! The only tool you will need is a straight longarm ruler. I also use my HQ Square foot which makes the whole process much easier.

Apply binding on the longarm

Along the way I am going to mention some different options you have for doing some of the steps. I suggest you try them all and see what works best for you.

Prepare your binding

Prepare your double fold binding as you normally would, at the width that you prefer, whether you use bias binding or straight grain binding. The binding needs to be at least 12-18 inches longer than the perimeter of the quilt top.
Tip: use a bit of spray starch, applying the starch to the wrong side of the binding as you press it in half, it acts like a glue that keeps the two sides of the binding firmly together and prevents the sides from shifting or separating during the application process.
Now you need to choose whether you will complete the entire binding on the frame or whether you will leave the last 10 or so inches to complete on your domestic machine.
  • complete the entire binding on the frame
    • open one end of the binding and cut on a 45 degree angle
    • press in a quarter inch fold on the end you just cut
    • press the binding back in half
    • Open binding and cut at a 45 degree angle
    • press in 1/4 inch fold
    • re-press in half
    • complete the binding on the domestic
      • no special prep required

    Applying binding after all quilting is complete.

    Quilt as you normally would, but do not remove the quilt from the frame. Be sure to baste the bottom edge of the quilt and remove from the leader if you had it attached.

    You will start on the right side about 10 inches up from the bottom corner (or as much as your throat space allows). Leave a 6-8 inch tail loose. If you are finishing completely on the frame start with the end you cut at an angle. Place the binding so that the raw edge of the binding lines up with the raw edge of the quilt. There are a few methods you can choose from:

    Using a Ruler

    • I like to use a ruler with tabs like the HQ Ditch Ruler or the HQ Mini Scallop ruler. The straight side of the HQ Versa Tool ruler works as well, although it is shorter than the other two. This holds the binding in place as you sew along the ruler edge.
      • Align the ruler at the raw edge of the quilt.  Place HQ Square foot against the ruler.
      • Make a few locking stitches and stitch ¼ inch away from the edge of the quilt along the ruler.
      • When you come to the lower right corner, position the ruler so that the inside of the tab is at the raw edge on the bottom of the quilt. Stop stitching ¼ inch from the bottom edge, or when the foot touches the ruler tab. Do a few locking stitches.
      • Do The Fold
      • – fold the binding to the right at a 90 degree angle to the right side of the quilt, aligning the raw edge of the binding with the bottom edge of the quilt. Finger press the mitered fold. Then fold the binding back on it self to the left, with the fold lined up with the right edge of the quilt. Align the raw edge of the binding with the raw edge of the bottom of the quilt.
      • Position your needle just off the fold, ¼ inch away from the bottom edge of the quilt. Make a few locking stitches and continue to stitch across the bottom of the quilt. When you come to ¼ inch from the left side of the quilt, tie off with locking stitches and repeat the fold. These photos show “Doing the Fold” at the bottom left corner and the top left corner of the quilt.
      • Ruler in place at the lower left edge. Note the placement of the tab.

         

        First fold at lower left corner

         

        Second fold at lower left corner

         

        Positioning foot

         

        Staring to stitch up left side

         

        First fold at top left corner

         

        Second fold at top left corner

         

      • Proceed in this manor stitching up the left side and across the top and down the right side. As you stitch up (or down) the sides, when you need to roll, leave the needle down in the quilt and very carefully and slowly roll the quilt. That way you can stitch a continuous seam.
      • As you stitch down the right side of the quilt, stop your stitching line approx 10 inches away from where you began, leaving the ends of the binding to be finished.
      • Remove the quilt from the frame and finish the binding on your domestic machine, attaching the ends of the binding with your favorite method.
      • Trim away excess backing and batting and the binding is now ready to be turned to the back side and stitched down either by hand or by machine, whatever is your preference.
    • If you prefer to finish the entire binding on the frame:
      • when you come close to where you started on the right side, smooth the beginning binding strip up in place and cut the ending binding about 1 inch past the miter on the beginning strip.
      • Tuck the raw end inside the mitered beginning strip. Then complete the stitching. The turned under edge on the binding will have to be hand stitched to keep the binding joined.
      • Now you can remove the quilt and trim the excess backing and batting. You are ready to turn the binding to the back and stitch.

    Free Motion

    • Just stitch down the binding keeping the edge of the hopping foot at the edge of the quilt. Be sure the binding stays smooth and be careful not to stretch the binding as you work. Hold the binding in place with one hand as you move your machine with the other hand. This is the best method for not-so-straight-or-square quilts where you will have to make adjustments and follow the edge of the quilt.

    Channel Lock

    • Channel lock really works well if the quilt is straight and square. Use the channel locks in place of the ruler. Once again, use one hand to hold binding in place and other hand to move the machine.

    I love to apply binding on the longarm! Wasn’t it easy?

    by Mary Beth Krapil

Ruler of the Month Club

If you have never joined the Ruler of the Month club with Handi Quilter, I’m here to fill you in on what it is all about.

What is it?

If you enjoy ruler work, you’ll love the opportunity to expand both your ruler collection and your ruler skills. Each month in the six-month series we introduce an exclusive, brand-new ruler to the Handi Quilter line-up. Along with the ruler, you’ll receive video education and design ideas. It’s a great way to gain ruler work confidence and build your skills.

Members get special pricing and exclusive access to the rulers during the 6 month club. That’s more than $50 total savings for all six rulers! At the end of the club, the rulers will become available on-line and at retailers for everyone.

When you complete all 6 months you will receive a special club member gift. ROMC8 will start in March and run through August.

How to Join

You sign up at a local retailer. Find one here.

If your retailer is not close to you, or if your local retailer is not participating, you can find a retailer who accepts participants and sends rulers via mail. Find one here. Simply type in your zip code and check the box “Ruler of the Month”. Once you find a few, give them a call and ask if you can join via mail.

You can ONLY participate through a retailer. You cannot join online at handiquilter.com.

ROMC8 Rulers

The theme for the Ruler of the Month Club 8 is Boundless Borders

Here are the featured rulers (shh – don’t tell anyone I showed them to you!).

March – On Point Template

ruler of the month 8

April – Swish (I think this will be my favorite!)

ruler of the month 8

May – Concave Curves

ruler of the month 8

June – Cable  (I think this will be my favorite!)  ((Can I have 2 favorites?))

ruler of the month 8

July – Diamond

ruler of the month 8

August – Pointed Arc

ruler of the month 8

And let’s not forget about the Club Member gift!

Looks pretty cool, right?  I know I can’t wait!

OH! one more thing, I almost forgot….

Every month, on the first Tuesday, be sure to tune in to HQ Watch and Learn on the Handi Quilter Facebook page. It’s at Noon Mountain time but you can find it on the Facebook page all week too. The Watch and Learn topic will be the club ruler for that month.

by Mary Beth Krapil

 

 

 

 

 

Go to Top