In this post and video, we'll load your Studio3 or Gallery3 Frame in ClearView (Position 2), step by step. Follow along with the video, or use the written steps below as a reference while you load your own quilt.
Loading happens in five phases: prepping your layers and frame, loading the backing, loading the quilt top, adding the batting and side clamps, and aligning and basting.
Phase 1: Frame Setup and Preparation
1. Prep your quilt layers
Start by sizing your quilt layers. Your backing should extend at least 4 inches beyond the quilt top on every side, and your batting at least 2 inches.
- Backing: 4–6 inches larger on each side
- Batting: 2 inches larger on each side
- Quilt top: as finished
If any of your fabric has a directional print, check which way it should face before you load it. Press any seams on your backing open.
2. Mark your centers
An easy way to mark your centers is to fold your backing in half and snip a small notch at the top and bottom centers. Fold the quilt top the same way and mark its centers with pins. If your leaders aren't already marked, mark the center of each one with a permanent marker.
3. Set the front pole arms
For ClearView, set both front pole arms to Position 2. At each front pole arm, remove the black knob, lower the front of the arm, and reinsert the knob into the lower hole. Tighten the knob securely, then check that both arms are set correctly in Position 2.
If you're using a Gallery3 frame, pull the knob to release the arm. Lower the arm until it clicks into the lower position. Repeat on the other side.
Frame refresher
Before you start loading, here's a quick frame refresher. In ClearView, the two front poles sit at different heights. The upper pole is your backing pole, and the lower pole is your quilt top pole. At the back, the idler pole sits just below the take-up pole.
Check leader direction
Check that every leader has the print side facing the back of the frame.
Phase 2: Loading the Backing
4. Drape the backing
Move your machine aside. Drape the backing wrong-side up over the take-up pole, then bring the bottom edge forward to the leader on the backing pole.
5. Pin the backing
Line up the edges and match the center marks. Starting at the center, pin out to each side. Space the pins about one to two finger-widths apart and about a quarter inch from the edge. On the last pin at each side, turn the pinhead out and weave the pin through the fabric a couple of times to secure the edge.
6. Roll the backing
Engage the ratchet stop on the backing pole, then roll the backing onto the pole, smoothing from the center out every few turns. Stop with twelve to eighteen inches hanging free.
7. Attach the take-up leader
Make sure the ratchet stop on the take-up pole is unlocked. Pull the take-up leader forward and under the idler pole, pulling it under the machine foot, until it meets the top edge of your backing. Align the centers, then pin from the center out, just like you did on the bottom.
8. Tension the backing
Engage the take-up ratchet stop, then turn the handwheel until the backing is smooth and firm. Stop with about two and a half to three inches of leader showing in front of the idler pole. Avoid over-tightening — the backing should still have a little give.
Phase 3: Loading the Quilt Top
9. Drape and pin the quilt top
Drape your quilt top right-side up over the backing, with the top edge toward the back of the frame. Release the ratchet stop on the quilt top pole and pull its leader up to meet the bottom edge of your quilt top. Align the center marks and pin from the center out, using the same method you used for the backing.
10. Roll the quilt top
Engage the ratchet stop on the quilt top pole. Roll your quilt top forward onto the pole, keeping any pieced seams straight and parallel to the pole as you go. Leave the top section unrolled so it's ready to drape over the batting, then move it out of the way for now.
Phase 4: Batting and Side Clamps
11. Insert the batting
To add the batting, release the ratchet stop and lift the quilt top pole into the cradles. Lay the batting across the backing, with the top edge about an inch below the take-up pins. Gently tuck the lower edge between the two front poles. Then smooth the batting from the center out.
If any batting is resting on the floor, drape it behind the lower storage pole. Lower the pole back into position and re-engage the ratchet stop.
12. Smooth the quilt top
Flip the quilt top back over the batting and smooth it from the center out. Position the top edge of the quilt about a half inch to an inch below the top of the batting. That leaves a little batting exposed for the plumb line you'll stitch next.
13. Attach the side clamps
Release the side clamp cords from the grabbers. Clamp the backing only, about an inch in from the edge, then secure the cords so there's light, even tension.
Phase 5: Aligning and Basting
14. Stitch a straight "plumb line"
Move the machine to the upper-left corner. Start by pulling up the bobbin thread:
- Hold the top thread with one hand, then press the needle up/down button to lower the needle. Press it again to bring the needle back up, then pull up the bobbin thread.
Next, engage your horizontal channel lock and select Baste mode. If you don't have Pro-Stitcher, use your manual channel lock instead. Then lower your stitches per inch to one of the presets for basting — 1/4" works great.
Fold the quilt top back, then stitch a straight line across the batting and backing. This gives you a plumb line to use as a guide when positioning your quilt top.
15. Align the quilt top
Align the top edge of your quilt top with that plumb line.
16. Baste the quilt top edge
Disengage the horizontal channel lock (or remove the manual channel lock).
Create a little slack in the thread, then bring the machine toward you. Lower the needle, then bring it back up. Pull up the top and bobbin threads, and snip them. Move your machine back to the upper-left corner, then pull up the bobbin thread again.
Re-engage the horizontal channel lock and baste across, staying within a quarter-inch seam allowance. Snip your thread.
17. Baste the sides
Disengage the horizontal channel lock and catch the bobbin thread.
If you're using Pro-Stitcher, engage the vertical channel lock. Without Pro-Stitcher, clip a manual channel lock onto one of the carriage wheels. Then baste down both sides of the quilt, within the seam allowance, as far as your quilting field allows. Each time you advance the quilt, baste the sides again to help keep everything straight and square.
Ready to Quilt
Your quilt is loaded in ClearView and ready to quilt.